2mm Custom Reef 2.0 Wetsuit Boots

Description

Next Level Warm-Water Performance

Recommended Water Temps: 15C/60F+

FULL DESCRIPTION

The 2mm Custom Reef 2.0 has been completely redesigned for even more durability and protection while still delivering Solite’s unmatched barefoot performance. 

KEY FEATURES

3D Molded Sole with Ballistic Laminate

Like all of our new 2.0 Series boots, the Reef features a one-piece, 3D molded 1mm natural rubber sole. The sole wraps up the toes and heel for increased durability and protection against rocks, urchins, and reef.  For additional urchin defense, we co-mold a flexible, puncture-resistant ballistic textile into the rubber sole. This invisible shield maintains barefoot feel while protecting your feet from urchin spines and razor-sharp coral.

Custom-Fit 2.0 Thermofoam Sole 

Our patented heat-moldable 2.0 Thermofoam Sole has also been completely redesigned including a more comfortable Mini-Split internal split toe. The Mini-Split is 1cm shorter than our prior internal split, improving fit and comfort for a wider variety of toe shapes while still maintaining precise control. The Thermfoam Sole is 4mm thick in the toes/heels for extra protection and 3mm elsewhere to avoid over-heating in tropical waters.

3-Point Strap with Floating D-Ring

Another Solite innovation, our 3-Point Strap anchors under both the arch and heel on the inside of the foot, and under the heel on the outside of the foot. When the strap is tightened, the boot snugs up evenly under the arch and through the rear of the boot, providing instant response and slop-free fit for all arch and ankle profiles. Our Floating D-Ring on the strap isn’t stitched in place, allowing it to “float” naturally to the optimal position on your foot. Our 3-Point Strap also is 100% Tatex-coated for extra durability and zero water absorption.

Breathable Ventiprene Upper with EZ-O Cuff

To prevent excess waterflow into the boot, we’ve updated the 2mm neoprene from perforated (2mm holes) to Ventiprene (microscopic holes), allowing the feet to breathe and stay cool without letting in water. This keeps your feet lighter for optimal quickness and dexterity. The Ventiprene foam is lined with our most abrasion-resistant Tuff Skin exterior lining and a quick-dry interior. We’ve had so much success with our EZ-O cuff design on our other boots, we adopted the design to our low-cuff styles. The EZ-O cuff provides a flush-resistant, low-bulk, seamless seal around the ankle without the need for cords or toggles.

Reinforced Stealth-Loop

To ease on/off, we’ve integrated our low-profile Stealth-Loop in the heel. The Stealth Loop is laminated between the neoprene and our co-molded rubber/textile heel reinforcement patch, providing incredible durability and pull-strength. The Stealth Loop is also Tatex-coated for extra strength and zero-water absorption. 

SIZE GUIDE

Sizing Tip: Order your regular shoe size or half a size down, as they expand to fit when moulded. For example, if you are a size 10.5, order a 10. If you are a size 10, also order a size 10. NOTE: If your feet are exceptionally narrow or low volume, you may want to size down even more. 

CHOOSING THE RIGHT SIZE

Solite Boots provide the absolute best performance, comfort, and warmth if they are sized and fit correctly. Here are some tips to make sure you get the correct size boots for optimum fit:

If you have Average/Wide Feet:

You should purchase your sneaker size or half a size smaller. Solite Boots should fit tight out of the box, but the heat molding process will stretch them to the perfect size. If your boots feel too big out of the box in any dimension (length/width/arch), then we suggest you try a size down. Even if they feel tight out of the box, heat molding will expand the boots to a snug but comfortable fit.

NOTE: If you plan to use the 1mm neoprene Heat Booster Socks inside your boots, you may not have to size down. In fact, if you have wide feet you may even want to size up half a size if you plan to use the 1mm neoprene Heat Booster Socks. For example, if you are a wide size 10.5 and plan to use the 1mm neoprene Heat Booster Socks, a size 11 may be a better fit. This is particularly applicable to the 5mm boots, which won’t stretch in heat-molding as much as 3mm boots.

If you have Narrow/Low-Volume Feet:

You can go down 1 size from your sneaker size. By heat-molding, the boot will stretch to fit your length, and narrow/reduce volume to hug your narrower foot. Once again, the 3mm Boots will stretch more easily in heat-molding than the 5mm boots, so keep this in mind when choosing.

HEAT MOLDING INSTRUCTIONS

Solite Boots are the world’s first and only custom, heat-moldable watersports footwear. Custom fitting can be done in your kitchen with nothing more than a kettle of boiling water. To heat-mold your Solite boots, watch the video below and follow the instructions carefully. Do not use any other methods of heat molding except boiling water. Use of ovens, microwaves, heat guns, etc. will void your warranty.

STEP-BY-STEP

1. Bring water to a boil (you will need approximately 3 cups of boiling water per boot.)

2. While water is heating, roll down the cuffs of your Solite boots and place them in a sink.

3. Put on your Solite Heat Booster socks. These socks will help allow for a little extra space when the boots are being molded.

4. Once water comes to a full bubbling boil, gently pour into your Solite boots (in the sink), filling each to slightly below the seam where the neoprene upper is attached to the sole. See photo.

5. Wait 5 minutes for the boiling water to soften the sole material.

6. After 5 minutes, carefully pour out the hot water from your Solite boot (doing one boot at a time) and quickly rinse out the inside of the boot with cold water to lower the surface temperature and to prevent burning. Test with your hand as you will want to get your foot in as warm as you can comfortably stand.

7. Place your foot inside your Solite boot while wearing the Heat Booster sock (if you plan to wear the socks inside the boots). Make sure your big-toe sits comfortably in the toe cavity and your heel is flush in the heel pocket.

8. Repeat Steps 6 and 7 for the other boot.

9. Secure boot ankle straps if you have them.

10. Walk around in your Solite boots for the next 10-15 minutes, to ensure a comfortable fit while the material cools and molds to your foot shape.

11. Once your Solite Boots have cooled to room temperature, the molding process is complete. 5-7 minutes.

12. If you are unhappy with the fit, you can re-mold your Solite boots repeating the same steps above. Your Solite boots should feel completely comfortable, almost like part of your foot.